SM-CMD5003 DVD- 2 DIN 7” TFT- 2 DIN Multimedia DVD receiver w
10Panel controlsFront panel1. EJECT button2. Reset button (hole)3. VOL- button4. Display5. VOL+ button6. TILT button7. POWER button8. MODE button9. TU
11Inner panel1. Memory card slot2. Panel status indicator3. Disc slotPanel status indicator lights up when youslide the panel down, flashes when youre
12Remote controller1. MODE button2. POWER button3. UP cursor button4. BND/RDM button5. ENTER button6. LEFT cursor button7. DOWN cursor button8. EJECT
13Changing the battery1. Press the catch and at the same time pull out the battery tray (pic. 1).2. Insert the 1 lithium battery, type CR2025 (3V) bat
14General operationsTouch screenDue to the touch screen, you can fulfill most functions not only by pressing buttons but also by touching theoptions y
15Mode selection Repeatedly press MODE button on the RC or on the panel to select amode: Radio => Disc => USB => SD => TV => AV-in. I
16System setupWhen you select SETTING mode or press SETUP button on the RC,the menu will be displayed, in which you can touch any item toperform opera
17 Backlight: select LOW, MID or HIGH display backlight level.RDS and Radio page Stereo: Select ON (stereo reception mode) or OFF (mono reception).
18 Clock setting: A touchable keyboard is displayed. Input the current time and touch OK to confirm.DVD page OSD lang: Select on-screen display lang
19Radio operationsUser interface of Radio modeWhen the unit is switched to Radio mode, the below touchableuser interface will be displayed on the disp
2Dear customer!Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefullybefore connecting, operating
20Manual/automatic tuning Manual tuning: press TUN/TRK / buttons on the panel or SEEK-/ and SEEK+/ on the RC and holdfor 2 seconds to enter the m
21TA (Traffic alarm) functionTouch TA button on the screen to switch on the TA function. When TA is on, the TA displays on TFT, or else, ifthere is no
22TV operations Connect a TV antenna to the TV antenna jack of the unit. Select TV mode. To access the TV mode menu, press MODE button on front pane
23Disc/USB/SD/MMC operationsUSB/SD/MMC notesUSB format supports 1.1. Capacity: up to 8 Gb.For correct and satisfactory operation, licensed SD/MMC memo
248. REPEAT button. Touch repeatedly to select repeat playback mode.9. SUBT button. Touch to select disc subtitle language.10. AUD button. Touch to se
2510. Volume down button. Touch to decrease volume.11. Volume level.12. Volume up button. Touch to increase volume.13. STOP button. Touch to stop play
26Press long repeatedly SEEK-/ or SEEK+/ buttons on the RC or press repeatedly TUN/TRK / buttons onthe panel or corresponding buttons on the scree
27Zooming in/outDuring playback of video or images on disc/USB/SD/MMC, press and hold repeatedly A-B/ZOOM button onthe RC, the picture will be zoomed
28ID3 Tag functionIf a MP3 file has ID3 tag information in the supported ID3 format, such information will be displayed on theLCD while playback.
29Handling compact discs Do not insert anything other than a CD into the CD loading slot. Do not use cracked, chipped, warped, or otherwise damaged
3Important safeguards Read carefully through the manual to familiarize yourself with this unit. Keep this manual handy as a reference for operating
30Troubleshooting guideBelow is a table describing simple measures that can help you eliminate most problems likely to emergewhen this unit is in use.
31Temperature inside the car is toohigh.Cool off until the ambient temperature returns tonormal.The built-in microcomputer is notoperating properly.Re
32SpecificationGeneralPower supply: 12 V DCMaximum power output: 4 x 50 WDimensions 165 x 100 x 178 mmMounting angle 0 to +/-300Working temperature ra
33! .
34 , .
35 , , .
361. 1 2. 1 3. 1 4. 1 5. ISO- 1
37 , ,
38 (5) . ( ).
39. ,, .:
4Accessories1. Receiver 1 pc2. Front panel 1 pc3. Protective bag 1 pc4. Remote controller 1 pc5. ISO connector 1 pc6. Audio-video connector 1 pc7. Mou
40
41 ISO1. ISO, , .2.
42, ,
431. EJECT2. () reset3. VOL-4. 5. VOL+6. TILT7. POWER8.
441. 2. 3. ,,
45 ()1. MODE2. POWER3. 4. BND/RDM5. ENTER6. 7.
461. , .2. (CR 2025 3V), .
47,
48 MUTE PWR .
49.
5Installation/Connections Choose the mounting location where the unit will not interfere with the normal driving function of thedriver. Before final
50 SETTING SETUP ,
51 (Display) Screen (): 16:9, 4:3 FULL (“”). Backlight ():
52.EON TA DX ( ):
53 : 4:3PS: ( ,); 4:3LB: (
54, ,
5517. . BAND/RDM
56 RDS RDS () . , RDS,
57 . .
58/USB/ SD/MMC USB/SD/MMC USB: USB 1.1. : 8 . SD/MMC:
596. . .7. . .8. REPEAT.
6 Place the trim ring (5) over the unit and the installation is completed. (Some vehicles may not need atrim ring). The device is distinguished by a
606. . .7. .8. MDC.
61/USB/ STOP/PBC . PLAY
62 INT , .
63 ( DVD) ANGLE , . ,
64 , . (
65, ,
66. ..,
67 1200FM 65 – 74 /87,5 – 108 18 AM (MW)
7Connection diagram
8Using the ISO Connector1. If your car is equipped with the ISO connector, then connect the ISO connectorsas illustrated.2. For connections without
9Parking wire connectionIf Parking cable is connected to hand brake switch, the video display of the TFT monitor will be controlled bydriving status,
Comentarios a estos manuales